Products

Used to directly access VBUS from a USB-C port. USB-C to screw terminal breakout cable, 30cm long, exposing VBUS, ground, shield, Side Band Unit 1/2.

Devantech dS3484 case. Includes mounting holes for fixing to a wall or back panel. This precision snap together case includes screws for mounting the dS3484 module.

Supplied as a case only, the dS3484 module should be ordered separately.

A precision case for Devantech ETH008.  Includes mounting holes for fixing to wall or back panel and includes all screws to mount the Devantech ETH008 relay board inside.  

Precisely machined mounting bracket for LightWare LW20 cut from ¼ in thick high-grade aluminum. Attach a LightWare LW20 (not included) to your robot or drone, protecting the sensor from most collisions. Mount the stand directly on the chassis, or on a digital servo (not included) for area-sweeping collision detection.

INTERFACE EFFICIENTLY: The Devantech USB to I2C module provides a complete interface between your PC and the I2C bus.

Adapter for communicating to I2C, SPI and serial buses from a USB port. Output pins may alternatively be configured as general purpose digital input/output and analog inputs.

A precision case for Devantech ETH002 relay board.   Includes screws for mounting the Devantech ETH002 relay module inside.  

Devantech self-powered USB to RS485 adapter with support for baud rates up to 250kbps, automatic bus turn-around, and buses up to 128 devices.

The Devantech SRF01 is the world’s smallest single transducer ultrasonic rangefinder. It’s got a single pin serial interface connection. The SRF01 can measure in cm or Inches. In standard mode the SRF01 measures from approx 18cm (7in) to 600cm (19ft). In Advanced mode it is possible for the SRF01 to measure range all the way down to zero.

USB-C to USB-C USB4 (40Gbps) cable with coaxial SuperSpeed lines, support for 5A charging. Ideal for use with the Acroname USB-C-Switch and the USBHub3c.

A specialized multiplexer that uses R/C servo signals as a basis for input control and output signals. The RxMux allows control of 8 R/C servos from two different input signal sources. Signal sources can come from R/C receivers, autopilots, or microcontrollers that are connected to the RxMux input pins. The RxMux is perfect for autonomous control of UAVs, drove and other remote control systems.

The Devantech SRF04 sonar range finder is a single-transducer ranging module with a 2-pin serial interface. With a range from 3cm to 3m (or 1.2in to 9.8ft), it’s ideal for situations that require accurate ranging information.

The SRF02 is a single transducer ultrasonic rangefinder in a small footprint PCB. This Devantech ultrasonic sonar ranging module has I2C and Serial interfaces with a range of 16 cm to 6 m (about 6 inches to 19 feet)

The SRF05 is a single transducer ultrasonic rangefinder with either a single pin for both trigger and echo, or separate trigger and echo pins.The SRF05 can be a drop-in replacement for the SRF04. The SRF05 returns a pulse proportional to distance that can measure from approx 1cm (0.4in) to 400cm (13ft).

This connector converts a serial or UART signal from TTL to RS-232 levels. Included are indicator LEDs for host serial power and TTL logic power.

Lightware Main Cable Type 1 is a 35cm long, single sided 7-pin female SM cable for SF10, SF11 and SF30 Lightware rangefinders.

LightWare 3D printed, ABS plastic mounting bracket for their LW20 sensor with 3 x M2 mounting holes.  

LightWare 3D printed servo bracket specifically for LW20 sensor and Corona DS-919MG servo (not included).

This serial adapter bridges UART serial data to USB as a virtual serial port. The connector allows you to communicate with a device that requires serial data at common serial baud rates.

USB-C® male to USB-A female adapter, 8" length with data transfer speeds up to 10 Gbps. For use with Acroname USB Hubs, Switches and beyond. Compatible with USB2 and USB3.

1.5ft, 10Gbps USB A male to USB-C male cable, 10Gbps, 3A for use with the 4-Port, Acroname USB-C Switch and beyond.   

Set of 2.54 mm (0.1 in) header pins to create a modular interface to the RxMux: 8-Channel 2:1 Servo Multiplexer.

USB 3.0 Type A to B Cable, 3-foot length. Used for USB Super-Speed data transfers up to 5Gbps, for use with Acroname USB Hubs and beyond. Compatible with USB 2.0 and 1.x.

Steel, right-angle, DIN rail mounting brackets for mounting Acroname's S77-USBHUB-2X4, S79-USBHUB-3P, S85-RDVR-USBCSW and S85-PASS-USBCSW products