Products
Products
The 40-pin USBStem module is a general purpose embedded I/O module with a USB 2.0 interface.
The National Institute of Standards and Technology (NIST) advances measurement science, standards, and technology for industries throughout the world. NIST certification means that the Acroname product you purchase and use has been tested against NIST standards and meets the exacting requirements required for safety and quality. One (1) business day processing or longer may be required.
ELEGANT CONNECTIONS: The S91-MTM-RCI-1 Ribbon Cable Interface connects non-MTM equipment into MTM-based systems. Bridge external test tools to an MTM test-point carrier board (TPCB) using wired ribbon cable, headers, or terminal blocks.
The S79-USBHUB-3P NIST Calibration Certificate provides formal documentation that Acroname Inc. has used NIST-Traceble test equipment to verify that the Vbus voltage and current measurements are within the limits specificed in the Typical Performance Characteristics section of the product datasheet. One (1) business day processing or longer may be required.
Extended, limited warranty for USBHub3+ (S79-USBHUB-3P) covering manufacturing defects.
A software add-on feature to enable control of the USBHub3c via RS232 serial interface on the external expansion header.
Software package which enables Qualcomm Quick Charge (QC2, QC3) support on ports 0-5.
Extended limited warranty for USB-C-Switch covering manufacturing defects.
The dS378 is an Ethernet connected relay module featuring 8 channels of 16Amp 250Vac relays. Each relay has both normally open (NO) and normally closed (NC) as well as the common available on three terminals. Create Peer to Peer control in just a few clicks with a powerful dScript programming language.
Extended, limited warranty for MTM-DAQ-2 (S92-MTM-DAQ-2) covering manufacturing defects.
Extended, limited warranty for MTM-IO-Serial (S62-MTM-IO-SERIAL) covering manufacturing defects.
The dS3484 Ethernet controlled relay board provides 8 digital switching I/O channels and 4 voltage-free contact relay outputs with a current rating of up to 16A each. Controlled over TCP/IP via Ethernet or USB for development.
The ETH008 Ethernet relay board provides 8 voltage-free contact relay outputs with a current rating of up to 16A each. This module is controlled over TCP/IP via Ethernet and is powered via 12VDC supply, either regulated or unregulated.
The dS1242 is an Ethernet connected relay module featuring 2 channels of 16Amp 250Vac relays. Each relay has both normally open (NO) and normally closed (NC) as well as the common available on three terminals.
Extended, limited warranty for USBHub2x4 (S797-USBHUB-2X4) covering manufacturing defects.
The USB-C Coaxial Universal Orientation Cable (UOC) enables automated testing of flipping USB-C connections. When used with the USB-C-Switch or USBHub3c, this cable provides an orientation-agnostic connection. It is built with low-loss coaxial wires for the USB SuperSpeed data lines to ensure the highest possible signal integrity in your USB-C test system. C67-USBC-UOC is a specialized USB-C UOC cable used for flip testing of USB-C end devices (cameras, flash drives, development boards) which short the USB 480Mbps A and B side D+/D- lines at the USB-C connector. Products which implement fully separated D+/D- connections for each side of the USB-C connector should use the C70-USB-UOC.
The USB-C Coaxial Universal Orientation Cable (UOC) enables automated testing of flipping USB-C connections. When used with the USB-C-Switch or USBHub3c, this cable provides an orientation-agnostic connection. It is built with low-loss coaxial wires for the USB SuperSpeed data lines to ensure the highest possible signal integrity in your USB-C test system. C70-USBC-UOC is a specialized USB-C UOC cable used for flip testing of USB-C end devices (cameras, flash drives, development boards) which implement fully separate USB 480Mbps A and B side D+/D- lines at the USB-C connector. Products which short D+/D- connections for A and B side of the USB-C connector should use the C67-USBC-UOC.
The USB-C Coaxial Universal Orientation Cable (UOC) enables automated testing of flipping USB-C connections. When used with the USB-C-Switch or USBHub3c, this cable provides an orientation-agnostic connection. It is built with low-loss coaxial wires for the USB SuperSpeed data lines to ensure the highest possible signal integrity in your USB-C test system. C46-USBC-UOC is a specialized USB-C UOC cable used for flip testing of USB-C end devices (cameras, flash drives, development boards) which short the USB 480Mbps A and B side D+/D- lines at the USB-C connector. Products which implement fully separated D+/D- connections for each side of the USB-C connector should use the C44-USBC-UOC.
The USBRLY16-B provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The processor is powered and instructed from any standard USB bus and the relay power is obtained by the DC power input adaptor.
This Devantech USB relay board provides 8 voltage-free contact latching relay outputs with a current rating of up to 16A each. Controlled and powered from any standard USB bus, no separate power supply is needed. Latching relays stay in their last position when power is removed.
This Devantech USB relay board provides 6 voltage-free contact relay outputs with a current rating of up to 16A each. Powered and controlled from any standard USB bus.
Case for Devantech d2832 Ethernet relay board. Includes mounting holes for fixing to a wall or back panel. This precision snap together case includes screws for mounting the dS2832 module.
Supplied as a case only, the dS2832 module should be ordered separately.
This Devantech 8-channel USB relay module is both powered and controlled by a standard USB bus hub. It uses relays with premium ultra-low power 50mW coil types, which means that the board’s consumption of current is less than 100mA, even with all the relays on, for excellent energy efficiency.