Devantech 8 Channel 16A USB Relay Module

Price

$70.00

The USBRLY16-B provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The processor is powered and instructed from any standard USB bus and the relay power is obtained by the DC power input adaptor.

SKU:

R326-USBRLY16

Manufactured by

Devantech

United Kingdom

Tabs

Overview

The DC input jack on this Devantech unit is 2.1mm with positive core polarity, DC supplies are required to supply at least 500mA at 12VDC. The relays are SPCO (Single Pole Change Over) types. The normally open, normally closed and common pins are all available on the screw terminals. This Devantech USB relay board provides 8 voltage-free contact relay outputs with a current rating of up to 16A each. Controlled from any standard USB bus.

Operating Temperature

-40C to +70C

Board Dimensions

LED indication

The USB-RLY16 provides a red LED mounted immediately next to each relay to indicate whether it is in a powered state (LED on), there is also two LED's which will flash with USB transactions to and from the module, green indicating reception of data from the PC and yellow the transmission of data to the PC. Finally there is red power LED mounted near to the USB connector.

Relay power rating

If the contact load voltage and current of the relay are in the region enclosed by the solid and dotted lines in the figure below, the relay can perform stable switching operation. If the relay is used at a voltage or current exceeding this region, the life of the contacts may be significantly shortened.

A full datasheet for the relays used on the RLY16 is here: RM85 datasheet

Features

Cadmium - free contacts
Height 15,7 mm
5000 V / 10 mm reinforced insulation
For PCB and plug-in sockets
Accessories: sockets and modules
AC and DC coils
Recyclable packing
Recognitions, certifications, directives: RoHS

Applications

First Step - Get The Drivers

The USB-RLY16 module uses the FTDI FT232R USB chip to handle all the USB protocols. The documentation provided by FTDI is very complete, and is not duplicated here. Before using the USB-RLY16, you will need to install FTDI's Virtual COM Port ( VCP ) Drivers. These drivers appear to the system as an extra Com Port ( in addition to any existing hardware Com Ports ). Application software accesses the USB device in the same way as it would access a standard Windows Com Port using the Windows VCOMM API calls or by using a Com Port Library. Drivers are available for Windows, Apple, Linux and Open BSD systems directly from the FTDI website. You should get and install the drivers now, before you connect the USB-RLY16 to your computer. The Drivers page is here.

Which COM port?

After installing the drivers, and plugging in the USB-RLY16 module to a spare USB port, you will want to know which COM port it has been assigned to. This will vary from system to system depending on how many COM ports you currently have installed. To find out where it is, right click on your "My Computer" desktop icon and select the "Device Manager" tab. Now scroll down and open the "Ports (COM & LPT)" tab. You should see the USB serial port listed - COM2 in the example below. If you want to change the COM port number - just right click on it, select properties, select advanced and select the COM port number from the available list. The COM port should be set up for 19200 baud, 8 data bits, no parity and two stop bits.

Commands

The USB-RLY16 operates with an easy to use command set as described in the table below. Most commands are only a single byte and if applicable the USB-RLY16 will automatically send its response. The only exception to this being the "Set relay states" command which requires and additional desired states byte to be sent immediately after the command byte.

Downloads

Links

Technical Documentation

Specs

Characteristics
Relays	8 SPCO (single pole change over)
Power	12V, DC adapter (not included)
Control Interface	USB
Relay Current	Up to 16A @ 24VDC or 250 VAC
Connections	Screw terminals for N/O, N/C and common contacts

Reviews