Acroname

Steel right angle mounting bracket for all Acroname Hubs and Switches; ships with x2 M3.5 and x2 M4 screws.

DIN rail mount with M3.5 screws, compatible with Acroname products S77-USBHUB-2X4, S79-USBHUB-3P and S85-USBC-SWITCH

Steel, right-angle, DIN rail mounting bracket with M3.5 screws for mounting Acroname's S77-USBHUB-2X4, S79-USBHUB-3P, S85-RDVR-USBCSW and S85-PASS-USBCSW products

 

Set of 2.54 mm (0.1 in) header pins to create a modular interface to the RxMux: 8-Channel 2:1 Servo Multiplexer.

USB-C® male to USB-A female adapter, 8" length with data transfer speeds up to 10 Gbps. For use with Acroname USB Hubs, Switches and beyond. Compatible with USB2 and USB3.

This serial adapter bridges UART serial data to USB as a virtual serial port. The connector allows you to communicate with a device that requires serial data at common serial baud rates.

This connector converts a serial or UART signal from TTL to RS-232 levels. Included are indicator LEDs for host serial power and TTL logic power.

A specialized multiplexer that uses R/C servo signals as a basis for input control and output signals. The RxMux allows control of 8 R/C servos from two different input signal sources. Signal sources can come from R/C receivers, autopilots, or microcontrollers that are connected to the RxMux input pins. The RxMux is perfect for autonomous control of UAVs, drove and other remote control systems.

Used for connecting external electronic loads to the USBHub3c for VBUS load testing. It features separate screw terminals for VBUS passthrough from each USB Type-C port (0 through 5). While this board provides a physical wiring interface to access each VBUS channel, the USBHub3c External Load Feature is required to enable VBUS outputs on the USBHub3c. Included with purchase of a USBHub3c with External Load add-on feature.

Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface. The Serial Control software feature for USBHub3c is required for this interface board to function. Included with purchase of a USBHub3c with Serial Control add-on feature.

Used to directly access VBUS from a USB-C port. USB-C to screw terminal breakout cable, 30cm long, exposing VBUS, ground, shield, Side Band Unit 1/2.

1M USB-C® to USB-C® USB4® coax cable supporting 40 Gbps,  Extended Power Range (EPR) 240W (48V 5A)

 

This breakout board provides easy access to the capabilities of Acroname 40-pin BrainStem, and is perfect for those looking to get started with the BrainStem. This breakout board can be powered from USB, ensuring a portable and easy-to-use development platform for 40-pin BrainStem.

Extended, limited warranty for MTM-USBStem (S69-MTM-USBSTEM) covering manufacturing defects.

Desktop-style AC to DC power adapter with 12VDC up to 5A (60W) output. Supports universal 100-240VAC input. Recommended for use with Acroname programmable USB hubs.

Extended, limited warranty for MTM-Relay (S78-MTM-RELAY) covering manufacturing defects.

The USB-C Coaxial Universal Orientation Cable (UOC) enables automated testing of flipping USB-C connections. When used with the USB-C-Switch or USBHub3c, this cable provides an orientation-agnostic connection. It is built with low-loss coaxial wires for the USB SuperSpeed data lines to ensure the highest possible signal integrity in your USB-C test system. C67-USBC-UOC is a specialized USB-C UOC cable used for flip testing of USB-C end devices (cameras, flash drives, development boards) which short the USB 480Mbps A and B side D+/D- lines at the USB-C connector. Products which implement fully separated D+/D- connections for each side of the USB-C connector should use the C70-USB-UOC.

The USB-C Coaxial Universal Orientation Cable (UOC) enables automated testing of flipping USB-C connections. When used with the USB-C-Switch or USBHub3c, this cable provides an orientation-agnostic connection. It is built with low-loss coaxial wires for the USB SuperSpeed data lines to ensure the highest possible signal integrity in your USB-C test system. C70-USBC-UOC is a specialized USB-C UOC cable used for flip testing of USB-C end devices (cameras, flash drives, development boards) which implement fully separate USB 480Mbps A and B side D+/D- lines at the USB-C connector. Products which short D+/D- connections for A and B side of the USB-C connector should use the C67-USBC-UOC.

Extended, limited warranty for USBHub2x4 (S797-USBHUB-2X4) covering manufacturing defects.

Extended, limited warranty for MTM-IO-Serial (S62-MTM-IO-SERIAL) covering manufacturing defects.

Extended, limited warranty for MTM-DAQ-2 (S92-MTM-DAQ-2) covering manufacturing defects.

Extended, limited warranty for USBHub3+ (S79-USBHUB-3P) covering manufacturing defects.

A software add-on feature to enable control of the USBHub3c via RS232 serial interface on the external expansion header.