Products

Steel right angle mounting bracket for all Acroname Hubs and Switches; ships with x2 M3.5 and x2 M4 screws.

The USBHub2x4 is a 4-port software-programmable 480Mbps (USB 2.0) hub that is designed for demanding industrial environments where advanced control and monitoring of USB ports is required. This is very useful in testing or development environments where standard “always-on” behavior of a consumer-grade USB hub is not desirable.

Steel, right-angle, DIN rail mounting bracket with M3.5 screws for mounting Acroname's S77-USBHUB-2X4, S79-USBHUB-3P, S85-RDVR-USBCSW and S85-PASS-USBCSW products

 

USB 3.0 Type A to B Cable, 3-foot length. Used for USB Super-Speed data transfers up to 5Gbps, for use with Acroname USB Hubs and beyond. Compatible with USB 2.0 and 1.x.

Set of 2.54 mm (0.1 in) header pins to create a modular interface to the RxMux: 8-Channel 2:1 Servo Multiplexer.

1.5ft, 10Gbps USB A male to USB-C male cable, 10Gbps, 3A for use with the 4-Port, Acroname USB-C Switch and beyond.   

USB-C® male to USB-A female adapter, 8" length with data transfer speeds up to 10 Gbps. For use with Acroname USB Hubs, Switches and beyond. Compatible with USB2 and USB3.

This serial adapter bridges UART serial data to USB as a virtual serial port. The connector allows you to communicate with a device that requires serial data at common serial baud rates.

The SRF05 is a single transducer ultrasonic rangefinder with either a single pin for both trigger and echo, or separate trigger and echo pins.The SRF05 can be a drop-in replacement for the SRF04. The SRF05 returns a pulse proportional to distance that can measure from approx 1cm (0.4in) to 400cm (13ft).

This connector converts a serial or UART signal from TTL to RS-232 levels. Included are indicator LEDs for host serial power and TTL logic power.

The SRF02 is a single transducer ultrasonic rangefinder in a small footprint PCB. This Devantech ultrasonic sonar ranging module has I2C and Serial interfaces with a range of 16 cm to 6 m (about 6 inches to 19 feet)

The Devantech SRF04 sonar range finder is a single-transducer ranging module with a 2-pin serial interface. With a range from 3cm to 3m (or 1.2in to 9.8ft), it’s ideal for situations that require accurate ranging information.

A specialized multiplexer that uses R/C servo signals as a basis for input control and output signals. The RxMux allows control of 8 R/C servos from two different input signal sources. Signal sources can come from R/C receivers, autopilots, or microcontrollers that are connected to the RxMux input pins. The RxMux is perfect for autonomous control of UAVs, drove and other remote control systems.

USB-C to USB-C USB4 (40Gbps) cable with coaxial SuperSpeed lines, support for 5A charging. Ideal for use with the Acroname USB-C-Switch and the USBHub3c.

The Devantech SRF01 is the world’s smallest single transducer ultrasonic rangefinder. It’s got a single pin serial interface connection. The SRF01 can measure in cm or Inches. In standard mode the SRF01 measures from approx 18cm (7in) to 600cm (19ft). In Advanced mode it is possible for the SRF01 to measure range all the way down to zero.

Devantech self-powered USB to RS485 adapter with support for baud rates up to 250kbps, automatic bus turn-around, and buses up to 128 devices.

A precision case for Devantech ETH002 relay board.   Includes screws for mounting the Devantech ETH002 relay module inside.  

This module has been discontinued by the manufacturer and replaced by the USB-ISS

INTERFACE EFFICIENTLY: The Devantech USB to I2C module provides a complete interface between your PC and the I2C bus.

Adapter for communicating to I2C, SPI and serial buses from a USB port. Output pins may alternatively be configured as general purpose digital input/output and analog inputs.

Devantech dS3484 case. Includes mounting holes for fixing to a wall or back panel. This precision snap together case includes screws for mounting the dS3484 module.

Supplied as a case only, the dS3484 module should be ordered separately.

A precision case for Devantech ETH008.  Includes mounting holes for fixing to wall or back panel and includes all screws to mount the Devantech ETH008 relay board inside.  

The USB-RLY82 USB controlled relay board provides 2 voltage-free contact relay outputs with a current rating of up to 16A each. Powered and controlled from the USB bus, this board features premium ultra low power 50mW coils.

Used for connecting external electronic loads to the USBHub3c for VBUS load testing. It features separate screw terminals for VBUS passthrough from each USB Type-C port (0 through 5). While this board provides a physical wiring interface to access each VBUS channel, the USBHub3c External Load Feature is required to enable VBUS outputs on the USBHub3c. Included with purchase of a USBHub3c with External Load add-on feature.