The SRF10 is a ultrasonic rangefinder with an I2C interface. The SRF10 can measure in cm or Inches from 3cm (1.2in) to 600cm (19ft).
The SRF02 is a single transducer ultrasonic rangefinder with both I2C and Serial interfaces. The SRF02 can measure in cm or Inches from approx 15cm (6in) to 600cm (19ft).
Devantech USB relay board provides 8 voltage-free contact relay outputs with a current rating of up to 1A each. Controlled from any standard USB bus.
This Devantech USB relay board provides 2 voltage-free contact relay outputs with a current rating of up to 16A each. Powered and controlled from any standard USB bus, does not require any additional power.
The SRF01 is a single transducer ultrasonic rangefinder in a very small footprint PCB with a single pin Serial interface. The SRF01 can measure in cm or Inches. In standard mode the SRF01 measures from approx 18cm (7in) to 600cm (19ft). In Advanced mode it is possible for the SRF01 to measure range all the way down to zero.
This Devantech USB relay board provides 8 voltage-free contact relay outputs with a current rating of up to 16A each. Controlled from any standard USB bus.
The ETH002 Ethernet relay board provides 2 voltage-free contact relay outputs with a current rating of up to 16A each. Controlled over TCP/IP via Ethernet.
The ETH008 Ethernet relay board provides 8 voltage-free contact relay outputs with a current rating of up to 16A each. Controlled over TCP/IP via Ethernet.
A precision case for Devantech ETH002 relay board. Includes screws for mounting the Devantech ETH002 relay module inside.
A precision case for Devantech ETH008. Includes mounting holes for fixing to wall or back panel and includes all screws to mount the Devantech ETH008 relay board inside.
The LightWare SF30/B is a high speed, light weight laser rangefinder for mapping and obstacle detection by robotic vehicles such as UAVs with a range up to 50m.
TeraRanger One is a lightweight, high-performance distance measurement sensor based on infrared time-of-flight (ToF) technology. Type A is best for use in indoor environments.
- TeraRanger One
Lightware Main Cable Type 1 is a 35cm long, single sided 7-pin female SM cable for SF10, SF11 and SF30 Lightware rangefinders.
The MTM system is designed to reduce the wiring complexity of manufacturing test systems. S73-MTM-DEV is a breakout board designed for development and test of embedded and high-level programs with common MTM modules. This kit includes all necessary cables to get started right out of the box.
Precision-machined bracket mounts a LightWare SF10, SF11 or SF30 series laser rangefinder to your project. Made of high-grade aluminum, it conveniently positions and protects the rangefinder in both stationary and mobile applications. Assembly is quick and easy and all necessary mounting hardware is included.
Aluminum bracket kit to conveniently mount a LightWare SF11-C Laser Rangefinder to an ELEV-8 v3 Quadcopter. Easy to mount to holes already present in the ELEV-8 v3 chassis plate, precision machined aluminum helps protect the rangefinder and positions it facing downward for accurate distance and altitude measurements. Takes no space beneath the quadcopter's bottom chassis plate, leaving plenty of room for other accessories.
TeraRanger Tower is a simultaneous multi-axis scanner. It is silent and has zero moving parts. It combines up to 8 TeraRanger One sensors and the TeraRanger Hub to create a scanner for SLAM (Simultaneous Localization and Mapping) and collision avoidance. Calibrated distance data is streamed from a USB or UART port as an array of synchronized distances, in millimetres. This model comes with 4 TeraRanger One sensors.
- TeraRanger Tower
The MTM-DAQ-1 data acquisition (DAQ) module provides 14 channels of single-ended analog inputs and 2-channels of bi-polar differential inputs at 16-bit resolution. Also included are two analog output (DAC) channels at 12-bit resolution. The MTM-DAQ-1 is optimized for precision analog measurements in manufacturing test, with selectable ranges from +/-64mV to +/-10.24V.
- MTM Analog IO Module
LightWare 3D printed servo bracket specifically for LW20 sensor and Corona DS-919MG servo (not included).
Precisely machined mounting bracket for LightWare LW20 cut from ¼ in thick high-grade aluminum. Attach a LightWare LW20 (not included) to your robot or drone, protecting the sensor from most collisions. Mount the stand directly on the chassis, or on a digital servo (not included) for area-sweeping collision detection.
USB-C Universal Orientation Cable (UOC) is a specialized USB-C cable for use only with Acroname's programmable USB-C-Switch. The C38-USBC-UOC cable provides an orientation-agnostic USB-C connection required for USB-C-Switch software-based cable flip functionality.
MTM-DEV-2 is a breakout board for MTM systems, which allows wire-wraps or ribbon cables to be directly attached to MTM modules for quick deployment of MTM in wire-wrapped testers.
MTM-RCI-1 is a wiring adapter used to adapt external equipment to wireless MTM test solutions. Using MTM-RCI-1, customers can bridge external test tools to an MTM test point carrier board (TPCB) using wired ribbon cable, headers or terminal blocks.