- 1 of 4
- next ›
The OPS243-C provides a simple radar sensor solution that can quickly and easily detect and report motion, speed, direction and range for objects in its field of view. A simple API enables a flexible solution that can be tailored for different applications. Full FCC/IC modular certification (pending) lowers development cost and time.
The OPS243-A provides a simple radar sensor solution that can quickly and easily detect and report motion, speed and direction for objects in its field of view. A simple API enables a flexible solution that can be tailored for different applications. Full FCC/IC modular certification (pending) lowers development cost and time.
The LightWare SF23/B is a very low power LiDAR that can be used in energy critical applications where batteries or solar cells are used. Weighing 10g, it can run from voltages as low as 3.2V and has an average current consumption of less than 2mA when taking one reading per second. The measuring range of the SF23/B is 0.2 to 50 meters, and features a serial interface.
The OPS241-B is an FMCW radar sensor solution that can reports the range to objects in its field of view at a range of up to 20m. A simple API enables a flexible solution that can be tailored for different applications.
Programmable software controlled USB hub with 2 host connections and 4 fast-charging (2.5A) device connections. Switch and control data, power and current limits separately. Boost USB signal levels to account for difficult interconnection environments. Rugged steel housing and ESD protected to 30kV.
Programmable, software-controlled, industrial USB 3.0 hub with 8 fast-charging (4A) ports, 2 host connections, and a dedicated port for control and monitoring. Control USB Hi-Speed, SuperSpeed data and power lines. Set current limit trip points for each port and monitor voltage and current on each port. Boost USB2 signal levels to account for difficult interconnection environments. Rugged steel housing and ESD protected to ±15kV (IEC61000-4-2 Level 4).
Software-controlled, bidirectional 4-channel USB-C port selector switch. Includes on-board USB signal redrivers for longer cables.
Automate port switching, hot-plug and type-C connector flips. Monitor Vbus and Vconn voltage and current. Support for USB-PD and alt-modes.
Rugged steel housing and ESD protected.
Includes one 1.5ft USB-C male-to-male full-featured, e-marked cable, one 1.5ft USB-C to A male-to-male cable and one 1.5ft Acroname Universal Orientation Cable (UOC).
The UST-05LX scanning laser rangefinder is a low power, small, accurate, high-speed device for obstacle detection. This model uses Ethernet interface for communication and can obtain measurement data in a 270° field of view up to a distance of 5 meters with millimeter resolution.
The TeraRanger Evo Thermal 33 is a compact and affordable thermal sensor with a 33° x 33° Field of View (FoV). With an update rate of 14 times a second and range of up to 13 meters, this sensor is ideal for Smart city, Smart building and Industrial applications.
The TeraRanger Evo Thermal 90 is a compact and affordable thermal sensor with a 90° x 90° Field of View (FoV). With an update rate of 7 times a second and range of up to 5 meters, this sensor is ideal for Smart city, Smart building and Industrial applications.
The TF03 is a cost-effective and compact long range (up to 180m) industrial level LiDAR sensor. With a blind spot of only 0.1m and accuracy of within 1%, this product is applicable to the terrain following of drones, the collision avoidance of cars, intelligent transportation and industrial safety warning.
The TFMini Plus is a single-point short-range ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object from 0.1m up to 12m. Unlike the original TFMini, the TFMini Plus has a full casing with an IP65 rating while still only weighing in at 11g.
The OPS242 is a complete short range radar sensor providing on board processing for motion detection, speed and direction reporting.
The Benewake CE30-D is a solid-state LiDAR with a 60° by 9° FoV. This sensor has a range of 0.4m (1.3ft) to 30m (98.4ft) with a 1cm (0.4inch) resolution. The CE30-D has no mechanical rotating components internally, and an IP65 rating which provides very high reliability and stability. With a UDP interface this sensor runs off of 12VDC.
YDLIDAR G4 is a 360º laser range scanner (LIDAR). With both a USB Type-C and PH2.0-5P bus interface, this sensor runs off of 5V and uses a brushless motor drive to scan at a sampling frequency of 9000 readings per second up to 16m (52.4ft) distances. YDLIDAR also has a user-friendly software interface and point cloud map to quickly get up and running with.
Ideal for precision analog measurements in manufacturing test, the MTM-DAQ-2 data acquisition (DAQ) module provides 16 channels of bi-polar differential inputs at 16-bit resolution with ranges as low as +/-64mV and as wide as +/-10.24V. Also included are two analog output (DAC) channels at 12-bit resolution with a range of +/-10.24V.
MTM-RCI-1 is a wiring adapter used to adapt external equipment to wireless MTM test solutions. Using MTM-RCI-1, customers can bridge external test tools to an MTM test point carrier board (TPCB) using wired ribbon cable, headers or terminal blocks.
MTM-DEV-2 is a breakout board for MTM systems, which allows wire-wraps or ribbon cables to be directly attached to MTM modules for quick deployment of MTM in wire-wrapped testers.
USB-C Universal Orientation Cable (UOC) is a specialized USB-C cable for use only with Acroname's programmable USB-C-Switch. The C38-USBC-UOC cable provides an orientation-agnostic USB-C connection required for USB-C-Switch software-based cable flip functionality.
Precisely machined mounting bracket for LightWare LW20 cut from ¼ in thick high-grade aluminum. Attach a LightWare LW20 (not included) to your robot or drone, protecting the sensor from most collisions. Mount the stand directly on the chassis, or on a digital servo (not included) for area-sweeping collision detection.
LightWare 3D printed servo bracket specifically for LW20 sensor and Corona DS-919MG servo (not included).
Aluminum bracket kit to conveniently mount a LightWare SF11-C Laser Rangefinder to an ELEV-8 v3 Quadcopter. Easy to mount to holes already present in the ELEV-8 v3 chassis plate, precision machined aluminum helps protect the rangefinder and positions it facing downward for accurate distance and altitude measurements. Takes no space beneath the quadcopter's bottom chassis plate, leaving plenty of room for other accessories.
Precision-machined bracket mounts a LightWare SF10, SF11 or SF30 series laser rangefinder to your project. Made of high-grade aluminum, it conveniently positions and protects the rangefinder in both stationary and mobile applications. Assembly is quick and easy and all necessary mounting hardware is included.